产品概述：Technical parameters: The technical indicators of each specification of this series are grouped into main output group, charging group, control lock group, outp···
technical parameter:
| project | Specifications of this series | |||
| grouping | main output group | charging pack | lock group | |
| output | DC output voltage | 18V | 20V | 12V |
| Rated output current | 0-3A | 0-0.5A | 0-2A | |
| Rated output power | 60W | |||
| Ripple and Noise① | <240mV | |||
| Load Regulation | <±0.5% | |||
| Incoming line adjustment rate | <±0.5% | |||
| enter | CL port | External 18VDC signal | ||
| Efficiency ( Typical ) ② | >82% | |||
| Input voltage range | 85-264VAC, 47Hz ~ 63Hz (120VDC ~ 370VDC) | |||
| Input inrush current | 110VAC/18A , 220VAC/36A | |||
| Maximum input operating current | <1.2A 110VAC <0.6A 220VAC | |||
| Start, rise, hold time | 200ms , 50ms , 20ms : 230VAC | |||
| Protect | Battery undervoltage protection | When the battery voltage is less than 17.5V, the circuit is open to stop discharging. | ||
| Overload protection | 105%-150% type: constant power overload 110-130% cut off output reset: disconnect or reduce the load | |||
| Short circuit protection | In the event of a short circuit at the output: the output is switched off. | |||
| Pressure resistance | Withstand voltage | Input-Output: 1.5KVAC Input-Case: 1.5KVAC Output-Case: 0.5KVAC for 1 minute | ||
| leakage current | Input-output ＜3.5mA at 1.5KVAC | |||
| leakage current | Input-output ＜0.3mA at 220VAC | |||
| Isolation resistance | Input - Output, Input - Case, Output - Case : 500VDC/100M Ω | |||
| other | Working temperature and humidity | -10 ℃～+50 ℃; 20% ～90RH | ||
| Storage temperature and humidity | -20 ℃～+85 ℃; 10% ～95RH | |||
| size | 159*98*38mm | |||
| Net weight/gross weight | 450/500g (lead-free battery) | |||
| Prepare enough | Note : ①When inputting 88VAC/176VAC ②When inputting 220VAC . You need to prepare 18 V lead- acid battery by yourself (recommended configuration current is ≥5 AH) | |||
| project | |||||
| output | DC voltage | 5V | 12V | 15V | 24V |
| Rated current | 3A | 1.67A | 1.33A | 0.84A | |
| rated power | 15W | 20W | 20W | 20.2W | |
| Ripple and Noise① | <80mV | <120mV | <120mV | <150mV | |
| Voltage accuracy | ±5% | ||||
| Load Regulation | ±2% | ||||
| Linear adjustment rate | ±1% | ||||
| Start, rise, hold time | 500ms, 20ms, 16ms: 115VAC 500ms, 20ms, 50ms: 230VAC | ||||
| enter | voltage range | 90-264VAC 47Hz～63Hz; 127VDC～370VDC | |||
| Efficiency ( Typical ) ② | >77% | >81% | >83% | >83% | |
| Working current | 0.55A/110VAC 0.35A/230VAC | ||||
| electric shock | 220VAC: 60A | ||||
| Protect | Overload protection | When the output rated power is greater than or equal to 105%-135%: Protection mode: hiccup mode, it can automatically recover after the abnormal condition is removed. | |||
| Overvoltage protection | When the output voltage is greater than or equal to 115%-145%: protection mode: hiccup mode, it can automatically recover after removing the abnormal condition. | ||||
| surroundings | Working temperature and humidity | -30℃～+70℃; 20%～90RH | |||
| Storage temperature and humidity | -40℃～+85℃; 10%～95RH | ||||
| Safety | Withstand voltage | Input-Output: 3KVAC for 1 minute | |||
| leakage current | Input-case ＜2.5mA at 240VAC | ||||
| Isolation resistance | Input-Output, Input-Case, Output-Case: 500VDC/100MΩ | ||||
| other | size | 117*29*20mm | |||
| Net weight/gross weight | 900/1200g | ||||
| Remark | ①Ripple and noise measurement method: use a 12" twisted pair cable, and the terminals should be connected in parallel with 0.1uF and 47uF capacitors, and measure at 20MHz bandwidth ②The efficiency is tested under the input voltage of 230VAC, the rated load, and the ambient temperature of 25℃. Accuracy: including setting error, linear adjustment rate and load adjustment rate. Linear Regulation Test Method: Test from Low Voltage to High Voltage at Rated Load Load regulation test method: from 0%-100% rated load. The start-up time is measured in a cold start state. Rapid and frequent switching of the machine may increase the start-up time. | ||||
| project | |||||
| output | DC voltage | 5V | 12V | 15V | 24V |
| Rated current | 4A | 2.5A | 2A | 1.25 | |
| rated power | 20W | 30W | 30W | 30W | |
| Ripple and Noise① | <80mV | <120mV | <120mV | <150mV | |
| Voltage accuracy | ±5% | ||||
| Load Regulation | ±2% | ||||
| Linear adjustment rate | ±1% | ||||
| Start, rise, hold time | 500ms, 20ms, 16ms: 115VAC 500ms, 20ms, 50ms: 230VAC | ||||
| enter | voltage range | 90-264VAC 47Hz～63Hz; 127VDC～370VDC | |||
| Efficiency ( Typical ) ② | >77% | >81% | >83% | >83% | |
| Working current | 1A/110VAC 0.65A/230VAC | ||||
| electric shock | 220VAC: 60A | ||||
| Protect | Overload protection | When the output rated power is greater than or equal to 105%-135%: Protection mode: hiccup mode, it can automatically recover after the abnormal condition is removed. | |||
| Overvoltage protection | When the output voltage is greater than or equal to 115%-145%: protection mode: hiccup mode, it can automatically recover after removing the abnormal condition. | ||||
| surroundings | Working temperature and humidity | -30℃～+70℃; 20%～90RH | |||
| Storage temperature and humidity | -40℃～+85℃; 10%～95RH | ||||
| Safety | Withstand voltage | Input-Output: 3KVAC for 1 minute | |||
| leakage current | Input-case ＜2.5mA at 240VAC | ||||
| Isolation resistance | Input-Output, Input-Case, Output-Case: 500VDC/100MΩ | ||||
| other | size | 220*29*20mm | |||
| Net weight/gross weight | 900/1200g | ||||
| Remark | ①Ripple and noise measurement method: use a 12" twisted pair cable, and the terminals should be connected in parallel with 0.1uF and 47uF capacitors, and measure at 20MHz bandwidth ②The efficiency is tested under the input voltage of 230VAC, the rated load, and the ambient temperature of 25℃. Accuracy: including setting error, linear adjustment rate and load adjustment rate. Linear Regulation Test Method: Test from Low Voltage to High Voltage at Rated Load Load regulation test method: from 0%-100% rated load. The start-up time is measured in a cold start state. Rapid and frequent switching of the machine may increase the start-up time. | ||||
| project | |||||
| output | DC voltage | 5V | 12V | 15V | 24V |
| Rated current | 10A | 5A | 4A | 2.5A | |
| rated power | 50W | 60W | 60W | 60W | |
| Ripple and Noise① | <80mV | <120mV | <120mV | <150mV | |
| Voltage accuracy | ±5% | ||||
| Load Regulation | ±2% | ||||
| Linear adjustment rate | ±1% | ||||
| Start, rise, hold time | 500ms, 20ms, 16ms: 115VAC 500ms, 20ms, 50ms: 230VAC | ||||
| enter | voltage range | 90-264VAC 47Hz～63Hz; 127VDC～370VDC | |||
| Efficiency ( Typical ) ② | >77% | >81% | >83% | >83% | |
| Working current | 1.5A/110VAC 1.1A/230VAC | ||||
| electric shock | 220VAC: 60A | ||||
| Protect | Overload protection | When the output rated power is greater than or equal to 105%-135%: Protection mode: hiccup mode, it can automatically recover after the abnormal condition is removed. | |||
| Overvoltage protection | When the output voltage is greater than or equal to 115%-145%: protection mode: hiccup mode, it can automatically recover after removing the abnormal condition. | ||||
| surroundings | Working temperature and humidity | -30℃～+70℃; 20%～90RH | |||
| Storage temperature and humidity | -40℃～+85℃; 10%～95RH | ||||
| Safety | Withstand voltage | Input-Output: 3KVAC for 1 minute | |||
| leakage current | Input-case ＜2.5mA at 240VAC | ||||
| Isolation resistance | Input-Output, Input-Case, Output-Case: 500VDC/100MΩ | ||||
| other | size | 168*48*33mm | |||
| Net weight/gross weight | 900/1200g | ||||
| Remark | ①Ripple and noise measurement method: use a 12" twisted pair cable, and the terminals should be connected in parallel with 0.1uF and 47uF capacitors, and measure at 20MHz bandwidth ②The efficiency is tested under the input voltage of 230VAC, the rated load, and the ambient temperature of 25℃. Accuracy: including setting error, linear adjustment rate and load adjustment rate. Linear Regulation Test Method: Test from Low Voltage to High Voltage at Rated Load Load regulation test method: from 0%-100% rated load. The start-up time is measured in a cold start state. Rapid and frequent switching of the machine may increase the start-up time. | ||||
| project | |||||
| output | DC voltage | 12V | 15V | 24V | 36V |
| Rated current | 25A | 20A | 12.5A | 8.3A | |
| rated power | 300W | 300W | 300W | 298.8W | |
| Ripple and Noise① | <120mV | <120mV | <200mV | <240mV | |
| Voltage accuracy | ±5% | ||||
| Load Regulation | ±2% | ||||
| Linear adjustment rate | ±1% | ||||
| Start, rise, hold time | 2000ms, 25ms, 15ms: 115VAC 2000ms, 25ms, 50ms: 230VAC | ||||
| enter | voltage range | 90-264VAC 47Hz～63Hz; 127VDC～370VDC | |||
| Efficiency ( Typical ) ② | >87% | >88% | >88% | >89% | |
| Working current | 4.5A/110VAC 2.7A/230VAC | ||||
| electric shock | 220VAC: 60A | ||||
| Protect | Overload protection | When the output rated power is greater than or equal to 105%-135%: Protection mode: hiccup mode, it can automatically recover after the abnormal condition is removed. | |||
| Overvoltage protection | When the output voltage is greater than or equal to 115%-145%: protection mode: hiccup mode, it can automatically recover after removing the abnormal condition. | ||||
| surroundings | Working temperature and humidity | -30℃～+70℃; 20%～90RH | |||
| Storage temperature and humidity | -40℃～+85℃; 10%～95RH | ||||
| Safety | Withstand voltage | Input-Output: 3KVAC for 1 minute | |||
| leakage current | Input-case ＜2.5mA at 240VAC | ||||
| Isolation resistance | Input-Output, Input-Case, Output-Case: 500VDC/100MΩ | ||||
| other | size | 220.4*130*48mm | |||
| Net weight/gross weight | 900/1200g | ||||
| Remark | ①Ripple and noise measurement method: use a 12" twisted pair cable, and the terminals should be connected in parallel with 0.1uF and 47uF capacitors, and measure at 20MHz bandwidth ②The efficiency is tested under the input voltage of 230VAC, the rated load, and the ambient temperature of 25℃. Accuracy: including setting error, linear adjustment rate and load adjustment rate. Linear Regulation Test Method: Test from Low Voltage to High Voltage at Rated Load Load regulation test method: from 0%-100% rated load. The start-up time is measured in a cold start state. Rapid and frequent switching of the machine may increase the start-up time. | ||||
